dmesg - optirun -c jpg
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 3.5.0-19-generic (buildd@komainu) (gcc version 4.7.2 (Ubuntu/Linaro 4.7.2-2ubuntu1) ) #30-Ubuntu SMP Tue Nov 13 17:48:01 UTC 2012 (Ubuntu 3.5.0-19.30-generic 3.5.7)
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
e820: BIOS-provided physical RAM map:
BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
BIOS-e820: [mem 0x0000000020200000-0x0000000040003fff] usable
BIOS-e820: [mem 0x0000000040004000-0x0000000040004fff] reserved
BIOS-e820: [mem 0x0000000040005000-0x0000000096abefff] usable
BIOS-e820: [mem 0x0000000096abf000-0x0000000096ebefff] reserved
BIOS-e820: [mem 0x0000000096ebf000-0x0000000096fbefff] ACPI NVS
BIOS-e820: [mem 0x0000000096fbf000-0x0000000096ffefff] ACPI data
BIOS-e820: [mem 0x0000000096fff000-0x0000000096ffffff] usable
BIOS-e820: [mem 0x0000000097000000-0x000000009f9fffff] reserved
BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
BIOS-e820: [mem 0x00000000feb00000-0x00000000feb03fff] reserved
BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
BIOS-e820: [mem 0x00000000ffc80000-0x00000000ffffffff] reserved
BIOS-e820: [mem 0x0000000100000000-0x000000025f5fffff] usable
NX (Execute Disable) protection: active
DMI 2.7 present.
DMI: Acer Aspire V3-571G/VA50_HC_CR, BIOS V1.06 04/20/2012
e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
e820: remove [mem 0x000a0000-0x000fffff] usable
No AGP bridge found
e820: last_pfn = 0x25f600 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-E7FFF write-protect
E8000-EFFFF write-combining
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 080000000 mask FE0000000 write-back
2 base 097000000 mask FFF000000 uncachable
3 base 098000000 mask FF8000000 uncachable
4 base 0FFC00000 mask FFFC00000 write-protect
5 base 100000000 mask F00000000 write-back
6 base 200000000 mask FC0000000 write-back
7 base 240000000 mask FE0000000 write-back
8 base 25F600000 mask FFFE00000 uncachable
9 base 25F800000 mask FFF800000 uncachable
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
e820: last_pfn = 0x97000 max_arch_pfn = 0x400000000
found SMP MP-table at [mem 0x000fe1b0-0x000fe1bf] mapped at [ffff8800000fe1b0]
initial memory mapped: [mem 0x00000000-0x1fffffff]
Base memory trampoline at [ffff880000097000] 97000 size 24576
init_memory_mapping: [mem 0x00000000-0x96ffffff]
[mem 0x00000000-0x96ffffff] page 2M
kernel direct mapping tables up to 0x96ffffff @ [mem 0x1fffc000-0x1fffffff]
init_memory_mapping: [mem 0x100000000-0x25f5fffff]
[mem 0x100000000-0x25f5fffff] page 2M
kernel direct mapping tables up to 0x25f5fffff @ [mem 0x96ab4000-0x96abefff]
RAMDISK: [mem 0x362e2000-0x37168fff]
ACPI: RSDP 00000000000fe020 00024 (v02 ACRSYS)
ACPI: XSDT 0000000096ffe210 00094 (v01 ACRSYS ACRPRDCT 00000001 01000013)
ACPI: FACP 0000000096ffb000 000F4 (v04 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: DSDT 0000000096fec000 0B783 (v01 ACRSYS ACRPRDCT 00000000 1025 00040000)
ACPI: FACS 0000000096fbb000 00040
ACPI: UEFI 0000000096ffd000 00236 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: ASF! 0000000096ffc000 000A5 (v32 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: HPET 0000000096ffa000 00038 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: APIC 0000000096ff9000 0008C (v02 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: MCFG 0000000096ff8000 0003C (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: SLIC 0000000096feb000 00176 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: SSDT 0000000096fea000 006FE (v01 ACRSYS ACRPRDCT 00001000 1025 00040000)
ACPI: BOOT 0000000096fe8000 00028 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: ASPT 0000000096fe3000 00034 (v07 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: FPDT 0000000096fe1000 00044 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: SSDT 0000000096fe0000 00968 (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
ACPI: SSDT 0000000096fdf000 00A92 (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
ACPI: SSDT 0000000096fdc000 0217A (v01 ACRSYS ACRPRDCT 00001000 1025 00040000)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at [mem 0x0000000000000000-0x000000025f5fffff]
Initmem setup node 0 [mem 0x00000000-0x25f5fffff]
NODE_DATA [mem 0x25f5fc000-0x25f5fffff]
[ffffea0000000000-ffffea00097fffff] PMD -> [ffff880256e00000-ffff88025ebfffff] on node 0
Zone ranges:
DMA [mem 0x00010000-0x00ffffff]
DMA32 [mem 0x01000000-0xffffffff]
Normal [mem 0x100000000-0x25f5fffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00010000-0x0009cfff]
node 0: [mem 0x00100000-0x1fffffff]
node 0: [mem 0x20200000-0x40003fff]
node 0: [mem 0x40005000-0x96abefff]
node 0: [mem 0x96fff000-0x96ffffff]
node 0: [mem 0x100000000-0x25f5fffff]
On node 0 totalpages: 2055756
DMA zone: 64 pages used for memmap
DMA zone: 6 pages reserved
DMA zone: 3911 pages, LIFO batch:0
DMA32 zone: 16320 pages used for memmap
DMA32 zone: 596223 pages, LIFO batch:31
Normal zone: 22488 pages used for memmap
Normal zone: 1416744 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
SMP: Allowing 8 CPUs, 4 hotplug CPUs
nr_irqs_gsi: 40
PM: Registered nosave memory: 000000000009d000 - 000000000009e000
PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
PM: Registered nosave memory: 0000000020000000 - 0000000020200000
PM: Registered nosave memory: 0000000040004000 - 0000000040005000
PM: Registered nosave memory: 0000000096abf000 - 0000000096ebf000
PM: Registered nosave memory: 0000000096ebf000 - 0000000096fbf000
PM: Registered nosave memory: 0000000096fbf000 - 0000000096fff000
PM: Registered nosave memory: 0000000097000000 - 000000009fa00000
PM: Registered nosave memory: 000000009fa00000 - 00000000e0000000
PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
PM: Registered nosave memory: 00000000f0000000 - 00000000feb00000
PM: Registered nosave memory: 00000000feb00000 - 00000000feb04000
PM: Registered nosave memory: 00000000feb04000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
PM: Registered nosave memory: 00000000fec01000 - 00000000fed10000
PM: Registered nosave memory: 00000000fed10000 - 00000000fed1a000
PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000
PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
PM: Registered nosave memory: 00000000fee01000 - 00000000ffc80000
PM: Registered nosave memory: 00000000ffc80000 - 0000000100000000
e820: [mem 0x9fa00000-0xdfffffff] available for PCI devices
Booting paravirtualized kernel on bare hardware
setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:8 nr_node_ids:1
PERCPU: Embedded 28 pages/cpu @ffff88025f200000 s83584 r8192 d22912 u262144
pcpu-alloc: s83584 r8192 d22912 u262144 alloc=1*2097152
pcpu-alloc: [0] 0 1 2 3 4 5 6 7
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2016878
Policy zone: Normal
PID hash table entries: 4096 (order: 3, 32768 bytes)
__ex_table already sorted, skipping sort
xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 7996304k/9951232k available (6716k kernel code, 1728208k absent, 226720k reserved, 6453k data, 928k init)
SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
Hierarchical RCU implementation.
RCU dyntick-idle grace-period acceleration is enabled.
NR_IRQS:16640 nr_irqs:744 16
Console: colour dummy device 80x25
console [tty0] enabled
allocated 33030144 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
hpet clockevent registered
Fast TSC calibration using PIT
Detected 2494.113 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 4988.22 BogoMIPS (lpj=9976452)
pid_max: default: 32768 minimum: 301
Security Framework initialized
AppArmor: AppArmor initialized
Yama: becoming mindful.
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys blkio
Initializing cgroup subsys perf_event
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
mce: CPU supports 7 MCE banks
CPU0: Thermal monitoring enabled (TM1)
using mwait in idle threads.
ACPI: Core revision 20120320
ftrace: allocating 25133 entries in 99 pages
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM) i5-3210M CPU @ 2.50GHz stepping 09
Performance Events: PEBS fmt1+, 16-deep LBR, SandyBridge events, Intel PMU driver.
... version: 3
... bit width: 48
... generic registers: 4
... value mask: 0000ffffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 000000070000000f
NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
Booting Node 0, Processors #1 #2 #3
Brought up 4 CPUs
Total of 4 processors activated (19952.90 BogoMIPS).
devtmpfs: initialized
EVM: security.selinux
EVM: security.SMACK64
EVM: security.capability
PM: Registering ACPI NVS region [mem 0x96ebf000-0x96fbefff] (1048576 bytes)
dummy:
RTC time: 21:31:19, date: 11/20/12
NET: Registered protocol family 16
Trying to unpack rootfs image as initramfs...
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
PCI: Using configuration type 1 for base access
bio: create slab at 0
ACPI: Added _OSI(Module Device)
ACPI: Added _OSI(Processor Device)
ACPI: Added _OSI(3.0 _SCP Extensions)
ACPI: Added _OSI(Processor Aggregator Device)
ACPI: EC: Look up EC in DSDT
ACPI: Executed 1 blocks of module-level executable AML code
[Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
ACPI: SSDT 0000000096e18018 0083B (v01 PmRef Cpu0Cst 00003001 INTL 20100121)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 0083B (v01 PmRef Cpu0Cst 00003001 INTL 20100121)
ACPI: SSDT 0000000096e19a98 00303 (v01 PmRef ApIst 00003000 INTL 20100121)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20100121)
ACPI: SSDT 0000000096e17d98 00119 (v01 PmRef ApCst 00003000 INTL 20100121)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20100121)
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
Freeing initrd memory: 14876k freed
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
ACPI: No dock devices found.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
_OSC request data:1 8 1f
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
pci_root PNP0A08:00: host bridge window [mem 0x9fa00000-0xfeafffff]
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: root bus resource [mem 0x9fa00000-0xfeafffff]
pci 0000:00:00.0: [8086:0154] type 00 class 0x060000
pci 0000:00:01.0: [8086:0151] type 01 class 0x060400
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:02.0: [8086:0166] type 00 class 0x030000
pci 0000:00:02.0: reg 10: [mem 0xb3000000-0xb33fffff 64bit]
pci 0000:00:02.0: reg 18: [mem 0xc0000000-0xcfffffff 64bit pref]
pci 0000:00:02.0: reg 20: [io 0x3000-0x303f]
pci 0000:00:14.0: [8086:1e31] type 00 class 0x0c0330
pci 0000:00:14.0: reg 10: [mem 0xb3600000-0xb360ffff 64bit]
pci 0000:00:14.0: PME# supported from D3hot D3cold
pci 0000:00:16.0: [8086:1e3a] type 00 class 0x078000
pci 0000:00:16.0: reg 10: [mem 0xb3614000-0xb361400f 64bit]
pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.0: [8086:1e2d] type 00 class 0x0c0320
pci 0000:00:1a.0: reg 10: [mem 0xb3619000-0xb36193ff]
pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: [8086:1e20] type 00 class 0x040300
pci 0000:00:1b.0: reg 10: [mem 0xb3610000-0xb3613fff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: [8086:1e10] type 01 class 0x060400
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: [8086:1e12] type 01 class 0x060400
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.0: [8086:1e26] type 00 class 0x0c0320
pci 0000:00:1d.0: reg 10: [mem 0xb3618000-0xb36183ff]
pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.0: [8086:1e57] type 00 class 0x060100
pci 0000:00:1f.2: [8086:1e03] type 00 class 0x010601
pci 0000:00:1f.2: reg 10: [io 0x3088-0x308f]
pci 0000:00:1f.2: reg 14: [io 0x3094-0x3097]
pci 0000:00:1f.2: reg 18: [io 0x3080-0x3087]
pci 0000:00:1f.2: reg 1c: [io 0x3090-0x3093]
pci 0000:00:1f.2: reg 20: [io 0x3060-0x307f]
pci 0000:00:1f.2: reg 24: [mem 0xb3617000-0xb36177ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.3: [8086:1e22] type 00 class 0x0c0500
pci 0000:00:1f.3: reg 10: [mem 0xb3615000-0xb36150ff 64bit]
pci 0000:00:1f.3: reg 20: [io 0x3040-0x305f]
pci 0000:01:00.0: [10de:0fd2] type 00 class 0x030000
pci 0000:01:00.0: reg 10: [mem 0xb2000000-0xb2ffffff]
pci 0000:01:00.0: reg 14: [mem 0xa0000000-0xafffffff 64bit pref]
pci 0000:01:00.0: reg 1c: [mem 0xb0000000-0xb1ffffff 64bit pref]
pci 0000:01:00.0: reg 24: [io 0x2000-0x207f]
pci 0000:01:00.0: reg 30: [mem 0xfff80000-0xffffffff pref]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:01.0: bridge window [mem 0xb2000000-0xb2ffffff]
pci 0000:00:01.0: bridge window [mem 0xa0000000-0xb1ffffff 64bit pref]
pci 0000:02:00.0: [14e4:16b5] type 00 class 0x020000
pci 0000:02:00.0: reg 10: [mem 0xb3430000-0xb343ffff 64bit pref]
pci 0000:02:00.0: reg 18: [mem 0xb3440000-0xb344ffff 64bit pref]
pci 0000:02:00.0: reg 30: [mem 0xfffff800-0xffffffff pref]
pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
pci 0000:02:00.1: [14e4:16bc] type 00 class 0x080501
pci 0000:02:00.1: reg 10: [mem 0xb3400000-0xb340ffff 64bit pref]
pci 0000:02:00.1: PME# supported from D0 D3hot D3cold
pci 0000:02:00.2: [14e4:16be] type 00 class 0x088000
pci 0000:02:00.2: reg 10: [mem 0xb3410000-0xb341ffff 64bit pref]
pci 0000:02:00.2: PME# supported from D0 D3hot D3cold
pci 0000:02:00.3: [14e4:16bf] type 00 class 0x088000
pci 0000:02:00.3: reg 10: [mem 0xb3420000-0xb342ffff 64bit pref]
pci 0000:02:00.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PCI bridge to [bus 02-02]
pci 0000:00:1c.0: bridge window [mem 0xb3400000-0xb34fffff 64bit pref]
pci 0000:03:00.0: [168c:0034] type 00 class 0x028000
pci 0000:03:00.0: reg 10: [mem 0xb3500000-0xb357ffff 64bit]
pci 0000:03:00.0: reg 30: [mem 0xffff0000-0xffffffff pref]
pci 0000:03:00.0: supports D1 D2
pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:1c.1: PCI bridge to [bus 03-03]
pci 0000:00:1c.1: bridge window [mem 0xb3500000-0xb35fffff]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG0._PRT]
_OSC request data:1 1f 1f
pci0000:00: Requesting ACPI _OSC control (0x1d)
_OSC request data:1 0 1d
pci0000:00: ACPI _OSC request failed (AE_ERROR), returned control mask: 0x1d
ACPI _OSC control for PCIe not granted, disabling ASPM
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 11 12 14 15) *7
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *7
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 10 *11 12 14 15)
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=none,locks=none
vgaarb: loaded
vgaarb: bridge control possible 0000:01:00.0
vgaarb: no bridge control possible 0000:00:02.0
SCSI subsystem initialized
libata version 3.00 loaded.
ACPI: bus type usb registered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
e820: reserve RAM buffer [mem 0x40004000-0x43ffffff]
e820: reserve RAM buffer [mem 0x96abf000-0x97ffffff]
e820: reserve RAM buffer [mem 0x97000000-0x97ffffff]
e820: reserve RAM buffer [mem 0x25f600000-0x25fffffff]
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
hpet0: 8 comparators, 64-bit 14.318180 MHz counter
Switching to clocksource hpet
AppArmor: AppArmor Filesystem Enabled
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: [bus 00-fe]
pnp 00:00: [io 0x0000-0x0cf7 window]
pnp 00:00: [io 0x0cf8-0x0cff]
pnp 00:00: [io 0x0d00-0xffff window]
pnp 00:00: [mem 0x000a0000-0x000bffff window]
pnp 00:00: [mem 0x000c0000-0x000c3fff window]
pnp 00:00: [mem 0x000c4000-0x000c7fff window]
pnp 00:00: [mem 0x000c8000-0x000cbfff window]
pnp 00:00: [mem 0x000cc000-0x000cffff window]
pnp 00:00: [mem 0x000d0000-0x000d3fff window]
pnp 00:00: [mem 0x000d4000-0x000d7fff window]
pnp 00:00: [mem 0x000d8000-0x000dbfff window]
pnp 00:00: [mem 0x000dc000-0x000dffff window]
pnp 00:00: [mem 0x000e0000-0x000e3fff window]
pnp 00:00: [mem 0x000e4000-0x000e7fff window]
pnp 00:00: [mem 0x000e8000-0x000ebfff window]
pnp 00:00: [mem 0x000ec000-0x000effff window]
pnp 00:00: [mem 0x000f0000-0x000fffff window]
pnp 00:00: [mem 0x9fa00000-0xfeafffff window]
pnp 00:00: [mem 0x00010000-0x0001ffff window]
pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
pnp 00:01: [io 0x0060]
pnp 00:01: [io 0x0064]
pnp 00:01: [irq 1]
pnp 00:01: Plug and Play ACPI device, IDs PNP0303 (active)
pnp 00:02: [irq 12]
pnp 00:02: Plug and Play ACPI device, IDs SYN1b16 SYN1b00 SYN0002 PNP0f13 (active)
pnp 00:03: [io 0x0000-0x001f]
pnp 00:03: [io 0x0081-0x0091]
pnp 00:03: [io 0x0093-0x009f]
pnp 00:03: [io 0x00c0-0x00df]
pnp 00:03: [dma 4]
pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
pnp 00:04: [mem 0xff010000-0xffffffff]
pnp 00:04: Plug and Play ACPI device, IDs INT0800 (active)
pnp 00:05: [mem 0xfed00000-0xfed003ff]
pnp 00:05: Plug and Play ACPI device, IDs PNP0103 (active)
pnp 00:06: [io 0x00f0]
pnp 00:06: [irq 13]
pnp 00:06: Plug and Play ACPI device, IDs PNP0c04 (active)
pnp 00:07: [io 0x002e-0x002f]
pnp 00:07: [io 0x004e-0x004f]
pnp 00:07: [io 0x0061]
pnp 00:07: [io 0x0063]
pnp 00:07: [io 0x0065]
pnp 00:07: [io 0x0067]
pnp 00:07: [io 0x0068]
pnp 00:07: [io 0x006c]
pnp 00:07: [io 0x0070]
pnp 00:07: [io 0x0080]
pnp 00:07: [io 0x0092]
pnp 00:07: [io 0x00b2-0x00b3]
pnp 00:07: [io 0x0680-0x069f]
pnp 00:07: [io 0xfd60-0xfd63]
pnp 00:07: [io 0x1000-0x100f]
pnp 00:07: [io 0xffff]
pnp 00:07: [io 0xffff]
pnp 00:07: [io 0x0400-0x0453]
pnp 00:07: [io 0x0458-0x047f]
pnp 00:07: [io 0x0500-0x057f]
pnp 00:07: [io 0x164e-0x164f]
system 00:07: [io 0x0680-0x069f] has been reserved
system 00:07: [io 0xfd60-0xfd63] has been reserved
system 00:07: [io 0x1000-0x100f] has been reserved
system 00:07: [io 0xffff] has been reserved
system 00:07: [io 0xffff] has been reserved
system 00:07: [io 0x0400-0x0453] has been reserved
system 00:07: [io 0x0458-0x047f] has been reserved
system 00:07: [io 0x0500-0x057f] has been reserved
system 00:07: [io 0x164e-0x164f] has been reserved
system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:08: [io 0x0070-0x0077]
pnp 00:08: [irq 8]
pnp 00:08: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:09: [io 0x0454-0x0457]
system 00:09: [io 0x0454-0x0457] has been reserved
system 00:09: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
pnp 00:0a: [mem 0xfed1c000-0xfed1ffff]
pnp 00:0a: [mem 0xfed10000-0xfed17fff]
pnp 00:0a: [mem 0xfed18000-0xfed18fff]
pnp 00:0a: [mem 0xfed19000-0xfed19fff]
pnp 00:0a: [mem 0xe0000000-0xefffffff]
pnp 00:0a: [mem 0xfed20000-0xfed3ffff]
pnp 00:0a: [mem 0xfed90000-0xfed93fff]
pnp 00:0a: [mem 0xff000000-0xff000fff]
pnp 00:0a: [mem 0xff010000-0xffffffff]
pnp 00:0a: [mem 0xfee00000-0xfeefffff]
pnp 00:0a: [mem 0x9fa00000-0x9fa00fff]
system 00:0a: [mem 0xfed1c000-0xfed1ffff] has been reserved
system 00:0a: [mem 0xfed10000-0xfed17fff] has been reserved
system 00:0a: [mem 0xfed18000-0xfed18fff] has been reserved
system 00:0a: [mem 0xfed19000-0xfed19fff] has been reserved
system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved
system 00:0a: [mem 0xfed20000-0xfed3ffff] has been reserved
system 00:0a: [mem 0xfed90000-0xfed93fff] has been reserved
system 00:0a: [mem 0xff000000-0xff000fff] has been reserved
system 00:0a: [mem 0xff010000-0xffffffff] could not be reserved
system 00:0a: [mem 0xfee00000-0xfeefffff] could not be reserved
system 00:0a: [mem 0x9fa00000-0x9fa00fff] has been reserved
system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0b: [mem 0x20000000-0x201fffff]
pnp 00:0b: [mem 0x40004000-0x40004fff]
system 00:0b: [mem 0x20000000-0x201fffff] has been reserved
system 00:0b: [mem 0x40004000-0x40004fff] has been reserved
system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
pci 0000:01:00.0: no compatible bridge window for [mem 0xfff80000-0xffffffff pref]
pci 0000:02:00.0: no compatible bridge window for [mem 0xfffff800-0xffffffff pref]
pci 0000:03:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref]
pci 0000:00:1c.0: BAR 14: assigned [mem 0x9fb00000-0x9fbfffff]
pci 0000:00:1c.1: BAR 15: assigned [mem 0x9fc00000-0x9fcfffff pref]
pci 0000:01:00.0: BAR 6: can't assign mem pref (size 0x80000)
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:01.0: bridge window [mem 0xb2000000-0xb2ffffff]
pci 0000:00:01.0: bridge window [mem 0xa0000000-0xb1ffffff 64bit pref]
pci 0000:02:00.0: BAR 6: assigned [mem 0xb3450000-0xb34507ff pref]
pci 0000:00:1c.0: PCI bridge to [bus 02-02]
pci 0000:00:1c.0: bridge window [mem 0x9fb00000-0x9fbfffff]
pci 0000:00:1c.0: bridge window [mem 0xb3400000-0xb34fffff 64bit pref]
pci 0000:03:00.0: BAR 6: assigned [mem 0x9fc00000-0x9fc0ffff pref]
pci 0000:00:1c.1: PCI bridge to [bus 03-03]
pci 0000:00:1c.1: bridge window [mem 0xb3500000-0xb35fffff]
pci 0000:00:1c.1: bridge window [mem 0x9fc00000-0x9fcfffff pref]
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 7 [mem 0x9fa00000-0xfeafffff]
pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
pci_bus 0000:01: resource 1 [mem 0xb2000000-0xb2ffffff]
pci_bus 0000:01: resource 2 [mem 0xa0000000-0xb1ffffff 64bit pref]
pci_bus 0000:02: resource 1 [mem 0x9fb00000-0x9fbfffff]
pci_bus 0000:02: resource 2 [mem 0xb3400000-0xb34fffff 64bit pref]
pci_bus 0000:03: resource 1 [mem 0xb3500000-0xb35fffff]
pci_bus 0000:03: resource 2 [mem 0x9fc00000-0x9fcfffff pref]
NET: Registered protocol family 2
IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP: reno registered
UDP hash table entries: 4096 (order: 5, 131072 bytes)
UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
NET: Registered protocol family 1
pci 0000:00:02.0: Boot video device
PCI: CLS 64 bytes, default 64
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
software IO TLB [mem 0x92ab4000-0x96ab3fff] (64MB) mapped at [ffff880092ab4000-ffff880096ab3fff]
Simple Boot Flag at 0x44 set to 0x1
audit: initializing netlink socket (disabled)
type=2000 audit(1353447078.540:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
fuse init (API version 7.19)
msgmni has been set to 15646
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
intel_idle: MWAIT substates: 0x21120
intel_idle: v0.4 model 0x3A
intel_idle: lapic_timer_reliable_states 0xffffffff
ACPI: AC Adapter [ACAD] (on-line)
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0C:00/input/input0
ACPI: Power Button [PWRB]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0D:00/input/input1
ACPI: Lid Switch [LID0]
input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0E:00/input/input2
ACPI: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
ACPI: Power Button [PWRF]
ACPI: Requesting acpi_cpufreq
ACPI: Battery Slot [BAT1] (battery present)
GHES: HEST is not enabled!
Linux agpgart interface v0.103
brd: module loaded
loop: module loaded
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
ahci: SSS flag set, parallel bus scan disabled
ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x5 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part ems apst
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m2048@0xb3617000 port 0xb3617100 irq 41
ata2: DUMMY
ata3: SATA max UDMA/133 abar m2048@0xb3617000 port 0xb3617200 irq 41
ata4: DUMMY
ata5: DUMMY
ata6: DUMMY
Fixed MDIO Bus: probed
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
PPP generic driver version 2.4.2
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.0: setting latency timer to 64
ehci_hcd 0000:00:1a.0: EHCI Host Controller
ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.0: debug port 2
ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
ehci_hcd 0000:00:1a.0: irq 16, io mem 0xb3619000
ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 3.5.0-19-generic ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci_hcd 0000:00:1d.0: setting latency timer to 64
ehci_hcd 0000:00:1d.0: EHCI Host Controller
ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.0: debug port 2
ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
ehci_hcd 0000:00:1d.0: irq 23, io mem 0xb3618000
ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 3.5.0-19-generic ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
xhci_hcd 0000:00:14.0: setting latency timer to 64
xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
xhci_hcd 0000:00:14.0: irq 21, io mem 0xb3600000
xhci_hcd 0000:00:14.0: irq 42 for MSI/MSI-X
usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: xHCI Host Controller
usb usb3: Manufacturer: Linux 3.5.0-19-generic xhci_hcd
usb usb3: SerialNumber: 0000:00:14.0
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: xHCI Host Controller
usb usb4: Manufacturer: Linux 3.5.0-19-generic xhci_hcd
usb usb4: SerialNumber: 0000:00:14.0
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 4 ports detected
usbcore: registered new interface driver libusual
i8042: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSS0] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mousedev: PS/2 mouse device common for all mice
rtc_cmos 00:08: RTC can wake from S4
rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected]
cpuidle: using governor ladder
cpuidle: using governor menu
EFI Variables Facility v0.08 2004-May-17
ashmem: initialized
TCP: cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
Key type dns_resolver registered
PM: Hibernation image not present or could not be loaded.
registered taskstats version 1
Key type trusted registered
Key type encrypted registered
Magic number: 4:241:551
tty ttyS27: hash matches
pci_link PNP0C0F:02: hash matches
rtc_cmos 00:08: setting system clock to 2012-11-20 21:31:19 UTC (1353447079)
BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
EDD information not available.
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[Firmware Bug]: battery: (dis)charge rate invalid.
ACPI: Battery Slot [BAT1] (battery present)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: ST9500325AS, 0001SDM1, max UDMA/133
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST9500325AS 0001 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb 1-1: new high-speed USB device number 2 using ehci_hcd
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
sd 0:0:0:0: [sda] Attached SCSI disk
usb 1-1: New USB device found, idVendor=8087, idProduct=0024
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 6 ports detected
usb 2-1: new high-speed USB device number 2 using ehci_hcd
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATAPI: Slimtype DVD A DS8A8SH, KA14, max UDMA/100
ata3.00: configured for UDMA/100
scsi 2:0:0:0: CD-ROM Slimtype DVD A DS8A8SH KA14 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
cdrom: Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
sr 2:0:0:0: Attached scsi generic sg1 type 5
Freeing unused kernel memory: 928k freed
Write protecting the kernel read-only data: 12288k
Freeing unused kernel memory: 1464k freed
Freeing unused kernel memory: 1120k freed
udevd[113]: starting version 175
tg3.c:v3.123 (March 21, 2012)
usb 2-1: New USB device found, idVendor=8087, idProduct=0024
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 8 ports detected
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
tg3 0000:02:00.0: eth0: Tigon3 [partno(BCM57785) rev 57785100] (PCI Express) MAC address dc:0e:a1:ab:06:d4
tg3 0000:02:00.0: eth0: attached PHY is 57765 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1])
tg3 0000:02:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
tg3 0000:02:00.0: eth0: dma_rwctrl[00000001] dma_mask[64-bit]
sdhci-pci 0000:02:00.1: SDHCI controller found [14e4:16bc] (rev 10)
sdhci-pci 0000:02:00.1: Invalid iomem size. You may experience problems.
mmc0: no vmmc regulator found
Registered led device: mmc0::
mmc0: SDHCI controller on PCI [0000:02:00.1] using ADMA
Refined TSC clocksource calibration: 2494.332 MHz.
Switching to clocksource tsc
usb 3-1: new low-speed USB device number 2 using xhci_hcd
usb 3-1: New USB device found, idVendor=046d, idProduct=c517
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1: Product: USB Receiver
usb 3-1: Manufacturer: Logitech
usb 3-1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
usb 3-1: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1:1.0/input/input5
logitech 0003:046D:C517.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:14.0-1/input0
logitech 0003:046D:C517.0002: fixing up Logitech keyboard report descriptor
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1:1.1/input/input6
logitech 0003:046D:C517.0002: input,hiddev0,hidraw1: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:14.0-1/input1
usb 3-2: new high-speed USB device number 3 using xhci_hcd
usb 3-2: New USB device found, idVendor=19d2, idProduct=1365
usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-2: Product: ZTE HSUSB Device
usb 3-2: Manufacturer: ZTE Incorporated
usb 3-2: SerialNumber: CSE_P729V
usb 3-2: ep 0x81 - rounding interval to 32768 microframes, ep desc says 0 microframes
usb 3-2: ep 0x1 - rounding interval to 32768 microframes, ep desc says 0 microframes
usb 1-1.1: new full-speed USB device number 3 using ehci_hcd
usb 1-1.1: string descriptor 0 read error: -22
usb 1-1.1: New USB device found, idVendor=0489, idProduct=e04e
usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1.3: new high-speed USB device number 4 using ehci_hcd
usb 1-1.3: New USB device found, idVendor=064e, idProduct=d20c
usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1.3: Product: 1.3M HD WebCam
usb 1-1.3: Manufacturer: SuYin
usb 1-1.3: SerialNumber: HF2015-A821-OV01-VA-R01.01.01
EXT4-fs (sda6): INFO: recovery required on readonly filesystem
EXT4-fs (sda6): write access will be enabled during recovery
EXT4-fs (sda6): recovery complete
EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
Adding 3905532k swap on /dev/sda5. Priority:-1 extents:1 across:3905532k
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udevd[381]: starting version 175
ACPI Warning: 0x0000000000000460-0x000000000000047f SystemIO conflicts with Region \PMIO 1 (20120320/utaddress-251)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
lpc_ich: Resource conflict(s) found affecting iTCO_wdt
ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMIO 1 (20120320/utaddress-251)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
ACPI Warning: 0x0000000000000500-0x000000000000053f SystemIO conflicts with Region \GPIO 1 (20120320/utaddress-251)
ACPI Warning: 0x0000000000000500-0x000000000000053f SystemIO conflicts with Region \_SB_.PCI0.PEG0.PEGP.GPIO 2 (20120320/utaddress-251)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
lpc_ich: Resource conflict(s) found affecting gpio_ich
mei 0000:00:16.0: setting latency timer to 64
mei 0000:00:16.0: irq 43 for MSI/MSI-X
lp: driver loaded but no devices found
[drm] Initialized drm 1.1.0 20060810
mei 0000:00:16.0: wd: failed to find the client
i915 0000:00:02.0: setting latency timer to 64
pci 0000:00:00.0: Intel Ivybridge Chipset
pci 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
pci 0000:00:00.0: detected 131072K stolen memory
Linux video capture interface: v2.00
uvcvideo: Found UVC 1.00 device 1.3M HD WebCam (064e:d20c)
i915 0000:00:02.0: irq 44 for MSI/MSI-X
[drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[drm] Driver supports precise vblank timestamp query.
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=none:owns=io+mem
vgaarb: transferring owner from PCI:0000:00:02.0 to PCI:0000:01:00.0
input: 1.3M HD WebCam as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input7
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
cfg80211: Calling CRDA to update world regulatory domain
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
usbcore: registered new interface driver btusb
wmi: Mapper loaded
ath: EEPROM regdomain: 0x6c
ath: EEPROM indicates we should expect a direct regpair map
ath: Country alpha2 being used: 00
ath: Regpair used: 0x6c
cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
cfg80211: Disabling freq 2484 MHz as custom regd has no rule that fits a 20 MHz wide channel
cfg80211: Updating information on frequency 5180 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5200 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5220 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5240 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5260 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5280 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5300 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5320 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5500 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5520 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5540 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5560 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5580 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5600 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5620 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5640 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5660 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5680 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5700 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5745 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5765 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5785 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5805 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Updating information on frequency 5825 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A mBi, 3000 mBm)
cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
Registered led device: ath9k-phy0
ieee80211 phy0: Atheros AR9462 Rev:2 mem=0xffffc90011980000, irq=17
microcode: CPU0 sig=0x306a9, pf=0x10, revision=0x12
acer_wmi: Acer Laptop ACPI-WMI Extras
acer_wmi: Function bitmap for Communication Button: 0x801
acer_wmi: Brightness must be controlled by acpi video driver
cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
input: Acer WMI hotkeys as /devices/virtual/input/input8
input: Acer BMA150 accelerometer as /devices/virtual/input/input9
type=1400 audit(1353439906.509:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=581 comm="apparmor_parser"
type=1400 audit(1353439906.509:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=682 comm="apparmor_parser"
type=1400 audit(1353439906.509:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=682 comm="apparmor_parser"
type=1400 audit(1353439906.509:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=682 comm="apparmor_parser"
type=1400 audit(1353439906.509:6): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=723 comm="apparmor_parser"
type=1400 audit(1353439906.509:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=581 comm="apparmor_parser"
type=1400 audit(1353439906.509:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=581 comm="apparmor_parser"
type=1400 audit(1353439906.509:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=723 comm="apparmor_parser"
type=1400 audit(1353439906.509:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=723 comm="apparmor_parser"
microcode: CPU1 sig=0x306a9, pf=0x10, revision=0x12
microcode: CPU2 sig=0x306a9, pf=0x10, revision=0x12
microcode: CPU3 sig=0x306a9, pf=0x10, revision=0x12
microcode: Microcode Update Driver: v2.00 , Peter Oruba
[drm] failed to retrieve link info, disabling eDP
usbcore: registered new interface driver cdc_ether
rndis_host 3-2:1.0: usb0: register 'rndis_host' at usb-0000:00:14.0-2, RNDIS device, 6e:39:db:b8:b5:9d
usbcore: registered new interface driver rndis_host
[drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 170x48
fb0: inteldrmfb frame buffer device
drm: registered panic notifier
[Firmware Bug]: ACPI(PEGP) defines _DOD but not _DOS
init: failsafe main process (891) killed by TERM signal
psmouse serio1: synaptics: Touchpad model: 1, fw: 7.4, id: 0x1e0b1, caps: 0xd04773/0xa40000/0xa0400
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input10
acpi device:39: registered as cooling_device4
ACPI: Video Device [PEGP] (multi-head: yes rom: yes post: no)
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:37/LNXVIDEO:00/input/input11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
ppdev: user-space parallel port driver
type=1400 audit(1353439907.753:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=978 comm="apparmor_parser"
acpi device:45: registered as cooling_device5
ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:01/input/input12
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
tg3 0000:02:00.0: irq 46 for MSI/MSI-X
tg3 0000:02:00.0: irq 47 for MSI/MSI-X
tg3 0000:02:00.0: irq 48 for MSI/MSI-X
tg3 0000:02:00.0: irq 49 for MSI/MSI-X
tg3 0000:02:00.0: irq 50 for MSI/MSI-X
bbswitch: version 0.4.2
bbswitch: Found integrated VGA device 0000:00:02.0: \_SB_.PCI0.GFX0
bbswitch: Found discrete VGA device 0000:01:00.0: \_SB_.PCI0.PEG0.PEGP
bbswitch: detected an Optimus _DSM function
bbswitch: Succesfully loaded. Discrete card 0000:01:00.0 is on
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: power state changed by ACPI to D3
init: alsa-restore main process (1092) terminated with status 19
init: lightdm main process (1129) killed by TERM signal
hda_codec: ALC269VB: SKU not ready 0x598301f0
input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
init: plymouth-stop pre-start process (1399) terminated with status 1
cfg80211: Found new beacon on frequency: 2472 MHz (Ch 13) on phy0
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: enabling device (0006 -> 0007)
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: enabling device (0006 -> 0007)
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci_raw_set_power_state: 73 callbacks suppressed
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
cfg80211: Found new beacon on frequency: 2467 MHz (Ch 12) on phy0
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012
bbswitch: disabling discrete graphics
bbswitch: Result of Optimus _DSM call: 11000059
pci 0000:01:00.0: Refused to change power state, currently in D0
pci 0000:01:00.0: power state changed by ACPI to D3
bbswitch: enabling discrete graphics
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
pci 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
nvidia 0000:01:00.0: power state changed by ACPI to D0
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=none,decodes=none:owns=none
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.64 Tue Oct 30 10:58:20 PDT 2012